The three steps of cleaning and maintenance of the pressure calibration table:
Construction Machinery
parts including Bulldozer, Wheel Loader , excavator, forklift, road roller
maintenance parts and wearing parts, Segment, end bit, cutting
edge, track shoe and other components are wear parts in the moving and working
process of the bulldozer. Our factory specializes in providing this kind of wear
resisting parts for shantui SD series bulldozers. Our production of the components
using advanced technology, high strength, wear resistance. Our company provides
standard type and swamp type track shoes assembly of full series of
bulldozers. The track adopts composite structure, with the features of good
traction adhesion and rotation performance, high walking speed, easy to slip,
super wear-resistant.
The idler is in front
of the whole frame, used to guide the track to run correctly, to prevent its
deviation and deviant. In addition to guide the correct operation of the track,
the idler also play the role of the supporting wheel, can increase the contact
area of the track on the ground, reducing the specific pressure, adjusting the
tension of the track and absorbing the impact load.
Shantui products including Diesel Forklift , Electric Forklift, heavy duty
forklift, Gasoline Forklift, container forklift, Side Loader , Pallet Truck ,
construction machinery including shantui bulldozer, wheel loader, crawler
excavator, road roller, generator set, motor grader, truck crane, construction
machinery parts, Shantui Parts , Cummins engine parts, komatsu parts, and other
machinery parts.
Construction Machinery Parts,Cummins Engine Spare Parts,Cummins Spare Parts,Komatsu Engine Parts SHANDONG VOLIN HEAVY MACHINERY CO.,LTD. , https://www.shantuimachinery.com
It is not difficult to clean and maintain the pressure calibration station. It is only necessary to know the precautions and follow the steps.
Pressure check bench maintenance steps are:
First, the pressure calibration table appearance wipe steps:
Wipe the surface of the pressure calibration table with a dry cotton cloth or a wiping paper first to wipe off the dust or oil. Pay careful attention to the surface of the calibration table so as not to injure the surface. After cleaning the surface, use a clean, fine dry cotton cloth with industrial alcohol to wipe the outer surface of the pressure calibration table, especially metal and non-metal surfaces.
Second, the pressure calibration station pressure output interface cleaning steps:
Firstly, the pressure output interface is unscrewed from the pressure calibration table, and the pressure output interface is carefully cleaned along the thread with a cotton swab dipped in industrial alcohol. After the thread is cleaned, the pressure output port on one side is blocked with a plug. Then, the pressure pump is used for the pressurization operation. After the pressurization, the residual impurities in the pressure calibration table will be discharged outside the calibration table together with the transformer oil. Therefore, before the pressurization, the oil absorption device needs to be prepared to clean the material and the transformer oil.
Third, the pressure calibration table stainless steel surface wipe steps:
Wipe the surface of the stainless steel with a fine cotton cloth or a wiping paper first to wipe off the dirt or grease left by the machine after the measurement. Then wipe the industrial alcohol with a clean dry cotton cloth to wipe the outer surface of the stainless steel. The volatile alcohol will naturally evaporate. If necessary, use stainless steel special maintenance oil and then wipe.
Fourth, the pressure calibration table mechanical rotation part: sub-dry friction part and lubrication part, dry friction part of the air bearing and toothless transmission mechanism of the distinction.
Dry friction part of the maintenance steps:
1. Wipe the surface with a dry cloth or wiping paper to wipe off dust or oil.
2. Blowers can also be used to blow off dust.
3. When necessary, use a clean, dry cotton cloth with industrial alcohol or high-grade lubricant to wipe the surface.
Lubrication section maintenance steps:
1. First wipe the dust with a fine cotton cloth.
2. Lubricate parts and add lube oil, or add by grease gun.
According to the above steps, regular cleaning and maintenance of the pressure calibration table can prolong the service life and achieve high working quality, which is what the user should always do.
September 03, 2019